Windsurfing Articles and Location Guides

AL360 Boom Modification

Boom Choice

See my original Boom Comparisons article from 2020 to see why I chose to buy an AL360 boom. I'm mostly still happy with it, but with a couple of modifications it can be a lot better.

Modifications

Apart from fitting the new-style boom "spring clips" that don't fall apart, these are the two mods that I've also done:

Note for reference that my 2019 AC-X needs a boom of 204 +/- 2, whereas the AL360 boom's 200 max is an extra 15cm in length (actually a bit less than that). So there is at least 10cm that could be removed. However, the 2023 AC-X requires 210 +/- 2, so it seems sensible to allow for that and only remove ~5cm. That would take the minimum setting down to 155, which is the maximum setting of my 4.2m sail.

1 - AL360 E3 Carbon tailend (boom end) : loop-loop-go replacement.

The North/Duotone tail-end fitting fits on the AL360 tail-piece absolutely perfectly - it just needs a single new screw-hole to secure it.

Drill off the existing rivet heads, remove the AL360 fitting and put it stright in the bin. Then screw on the North (Duotone) part instead. An instant and massive improvement! (no more losing outhaul tension whilst sailing).

The only problem will be soucing the part, if it's still available (it's this one - p/n 9008415860081). Here's a picture showing how perfectly it fits:

North End on AL360 E3 Carbon

The part that I used came off a VERY old North Progression Comp boom, but it's the same part as used on all the recent Silver-series booms. (Don't use one of the transparent plastic ones though, as they're made of the wrong kind of plastic and don't last very long before breaking. The softer black or grey plastic ones last forever).

Just one important thing - when you drill the small hole for the single new fixing screw, make sure that you leave a very smooth radius on the hole (using a countersink bit and sanding if required) to avoid leaving any possible stress-concentrators.

2 - AL360 E3 Carbon : boom shortening.

This is actually quite straightforward but a little scary, and there are some very important points to note if you're considering doing something similar. These points probably apply to any boom, but they are particularly things that I've found when modifying the AL360.

Summary:

Here's the process in pictures:

1 - Sawing

I wanted to remove about 60mm(1), which is conveniently the length of the clip fitting so I just cut it right at the interface with a junior hacksaw. In the picture below the grip has already been trimmed back by the required amount (50mm back from the cut) so that the new end-fitting will overlap it by about 5mm.

1-Sawing

(1) The 60mm choice was with hindsight perhaps a mistake. 48mm (two holes) would have been better because the tail-piece won't sink another 60mm into the boom arms. I only found this out after making the cut. This means that I need to shorten the tail-piece a little bit too (24mm in my case).

(2) On my particular boom, the left-hand arm allowed the tail to slide in almost exactly 48mm, but the right-hand one only allowed about 40mm. I fixed this in an extremely risky way by clearing (reaming) out the arm a little bit (see later). I would not advise this!

What I would recommend (knowing this now) is to get a piece of 22mm tube (copper water pipe is perfect) and see how far it will sink into the boom arms before you decide how much to trim off. You can then make an informed decision…

2 - Checking

The holes were then checked for size. The moulded tail-piece holes are 6mm dia, and the holes in the boom arms for the pins are 6.5mm (not yet drilled).

2-Checking

3 - Jigging

I wanted to get the holes perfectly located and square to the tube arms, so I made this jig to help the drilling process. The holes in the thick top-piece were drilled on a drill press (pillar-drill) to get them perfectly vertical.

3-Jigging

4 - Drilling

Using a jig, the drilling process is easy. The deep holes keep the drill vertical and the locating "Notch" on the tube-ends is made by partially inserting each arm into the jig after the two main holes have been drilled.

4-Drilling

5 - Reaming

Because I'd removed more of the boom arm than perhaps I should have, I needed to get the right-hand side to allow a little more depth. After some investigation with an endoscope, I bought a 23mm core drill and modified it to take a very long shaft. With some VERY careful reaming, I gained an extra 10mm depth without reaching or disturbing the joint in the boom arms. I think this is okay but I would certainly not recommend it. Pictures just for info!

5-Reaming

You can see here where the two sections of boom arm meet, and where I've opened the tube up a little on the RHS (only). For reference, the hole-saw was this one. I just needed to drill down through the shank so that I could use a long bar as an arbor.

6 - Fitting

The newly-purchased end-fittings can then be fitted and held in place by a little bit of silicone sealant (the original used the same contact adhesive as holds the boom grip, so that's an option too). I'll probably add a dab of epoxy later. They should be glued in place with the clip attached (pins through the holes in the boom arm), but only once a check has been made with the tail-end inserted so make sure that the holes all line up and that the clips fit smoothly.

6-Fitting

6 - Trimming

Now the tail-piece ends need trimming-down by the same amount (i.e. shortening). Check how far they will go into the boom arms once they themselves have been shortened and reduce the tail-piece by the minimum amount possible. The picture below shows the joint within the boom arms that prevent the tail-piece from going in as far as you'd think by measuring externally (picture taken with an endoscope). This picture was taken before the reaming step (5) was done.

7-Trimming

Be very careful because the point at which the arms won't go in any further appears to be a lap-joint of two carbon tube mouldings, at the point where the circular arms meet the "egg-shaped" section towards the front. Don't be temped to "drill out" the obstuction otherwise you'll probably destroy the boom.

7 - Finishing

Here's the shortened boom once reassembled. Unfortunately there's no easy way of correcting the markings that are an integral part of the boom grip!

8-Finishing

8 - Laughing

I discovered whilst carefully measuring up for this modification that AL360's boom markings are not to scale! The 0 to +60 range printed on the arms is actually only +58.5cm…

North End on AL360 E3 Carbon

You must therefore be very careful if you're modifying one of these booms to fit a particular sail exactly. Make sure that you rig it and take measurements first and don't take the markings for granted. I'm tempted to ask for a refund of 2/60ths of what I paid, which is around £15 of boom that I don't actually have ;)


Finally a warning - doing any of this will very obviously void your warranty, might weaken your boom, and might leave you out at sea and in the sh!t if the boom breaks. It's probably best not to do this unless you're very confident and keep yourself safe when sailing.

Web Analytics